Related topics

PC will not POST or boot after Audigy card fitted
I'm no owned dog. excessive jury duty and your swift boot to the head routine has caught up to you. Bullshit. In 35 years of being a registered voter, I have served on precisely two juries If you weren't drunk that night, you're going to prison after the video evidence shows your most flagrant error to date.

Can't upgrade 2000sp2 to sp4
But if I go back into it and change anything else I get the no video beep syndrome. I have to reset to the default settings and start over. Anyone seen this? I have a Transcend mobo doing the same thing, only worse. Both machines work fine and my Soyo board is great because the BIOS is set how I want it,

Strange startup Vista
Athlon 1800+ 512mb DDR Nothing else attached apart from generic TNT video card No video signal Hard and froppy drives removed - bits everywhere PS All fans on board working Keyboard LEDS flsh as it tries to POST Tony PPS Two hours to go before I jump from the 12th floor -- OGPE24HSHD.

HELP! KT3 Won't boot after changing multiplier!!!
Someone mentioned that it could be a video card problem or a bad CPU issue. Note that this started after I had to reset after a defrag (attempt) that ran for more than a day. I had to reset after 80% completion as machine seemed to have hanged. There were no chirps from the machine CPU (dead?

Patrick Humphrey Death Watch
This has happened on 10 or more systems, so I believe there is some trick to restoring the CMOS to a default state, without having the video display working. (perhpas RS232 ??) After applying power, there is NO video display, not floppy drive activity, no smoke (or flames) nothing. Of course, I will is too cheap to

Windows won't boot after failed video card installation - HELP!
Frans Pop elen...@planet.nl linux debian bugs rc Package: xserver-xorg-video-intel Version: 2:2.2.0.90-3 Severity: serious When I switch from my X ...... No, I don't. (II) resource ranges after preInit: [0] 0 0 0x90380000 - 0x903bffff (0x40000) MS[B] [1] 0 0 0x80000000 - 0x8fffffff (0x10000000) MS[B] [2] 0 0

No video and no keyboard after video card removal
DualBooter dontmai...@domain.com microsoft public windowsxp help_and_support Hmm... a reinstall may be the only way- but if it didn't work under Safe Mode but you can see the start-up screen then your monitor/graphics card aren't dead... Yep, reinstall Windows XP. -- "Joe Selman" <j...@idlehero.com> wrote in message

What an awfull couple of days!
When I put the case back on and fired it up I got no video. So I took out that card and replaced it with another PCI card with no luck then yet another PCI card I have no video, and no keyboard. I don't get any beeps with the boot but sometimes if I turn off the monitor while the computer is running and turn it

Interesting prob here
OSTIAANTIC ostiaan...@aol.com comp sys mac hardware misc Both the Quadra 605 and the Performa 6115 will not start up correctly, ie. no video, if the PRAM battery is dead or I have fooled with them for hours after a successful startup with no problems at all. Does anyone have any idea at all what I can do?

No video output after compiling the kernel
I made sure that no video caching or shadowing was enabled. All to no avail. I'm hoping like crazy that I don't have to reformat my hard disk and reinstall Another thought (I'm remembering a different machine with similar fault - only this was after inserting a new network card) Re-seat all your memory simms.

SCSI Installation Problem:2940UW change in PCI slot caused ...
Video became garbled,so returned to settings assigned by computer after 2490UW installation. -2-Followed adaptec installation tips to resolve conflicts by No video display , no POST, no Floppy drive LED light, cannot turn computer off by front power button. Must turn off by power switch located on back of

SBS2003 wont boot after a windos update hotfix
Everything appeared to be going fine; the progress bar appeared at the bottom of the screen (after reboot w/ programming button). About ¾ of the way thorough this process, the machine powered down. Since that happened, I have been unable to get as much as the Mac startup sound out of the machine. No video, no sound

Warp 4 and S3 2.84.14 - Mini howto
The server gives no error messages or blue screen. When the server boots it looks to start up as normal, displaying the Windows Server 2003 splash screen then i goes black and nothing more Do you remember exactly what you installed? I was thinking video driver but if you can't TS to the system from another one?

tv wonder - no boot after install
I then cleared again, set the FSB to 100 mhz, shut down, taped B21, re-installed the Celeron and got the same result: no boot, no video signal. I tied a couple more times, same result. NOTE: I also tried to reboot WITH B21 taped AFTER clearing the bios jumper to default; the result of that attempt was not only no-

All-in-Wonder locks up computer on cold boot - fine after reset
Then, if you have no other way to get back your current display adapter, you may go back into that screen to select it. ......Quote.......... The first thing to do is to remove the video adapter you have installed. Right-click on the desktop; choose "Properties" from the drop-down menu; select "Settings;" click on

NT 4 boot kills video signal for 5 cold restarts?!?
I think the card might be sending the video signal out the NTSC output, but I have no TV handy here at work to confirm. Safe mode works fine of course. I think that I've installed what are the latest drivers from the ATI site and that didn't seem to help things. One note, I had this card in the same machine running

No video on boot on Pavilion 4530
On initial bootup I had no video at all and no floppy light, however the HD drive lights, fans, CDRom lights and power lights all came on. I did a BIOS recovery and everything went as described...Power on, floppy light on, then HD. After a couple of seconds the floppy light came back on and I could hear it working,

No Video after boot, safe mode + VGA mode doesn't help
Occasionally, when I turn the machine on from the main power switch, it hangs with no video display (monitor shows no-signal light). The hard disks spin up and the IDE LED remains on In my case, though, it just seemed to disappear after a while, without any modification to the hardware or settings whatsoever.

reviving old 9600
So I dug out a Viewsonic E771, but still no video. Strange. Then I figured it's the graphics card, so I put an Elsa GF2 in, but no change. After a few of these reboots I can't even get where I can see the BIOS screen. If I let the computer boot up into Windows, I can turn on the monitor and see the Windows

850GB + P4/1.5GHz => No boot / no video
Voila- the HDD started flickering up again and I suspect that the operating system is actually running... except my monitor is getting no video!! I tried to repair the installation and I've run the installation from scratch.. all to no avail. My initial instance of WinXP Pro works just fine whenever I decide to