Related topics

A7V8X-MX installation problem; no video after first boot
HIT NO! It's okay to overwrite the other files. 5) Everything should be okay after installing, if not post in os2.video. Don't send e-mail, I'm no video guru, but another user trying to help another user. 6) It might not be a bad ideal to make copies of the critical files so you can just copy over the wrong version

Computer won't boot
But offered no solution. I did have to re-load my viper drivers after flashing because the graphics were terrible and it did correct it. Do you think there could be a fight going on .... Because of the small amount of code available in the non-erasable boot block area, no video is available to direct the procedure.

KG6 will not POST or boot after soundblaster Audigy card
Ian Wienand i...@ieee.org linux debian bugs dist linux debian maint x Package: xserver-xorg-video-intel Version: 2:2.2.1-1 Severity: normal Hi Whenever I ..... No, I don't. (II) resource ranges after preInit: [0] 0 0 0xdfec0000 - 0xdfefffff (0x40000) MS[B] [1] 0 0 0xc0000000 - 0xcfffffff (0x10000000) MS[B] [2] 0 0

P6sne: dead after shut off for 3 months?
Get a call saying that he's having the no-video problem again and I go over to help troubleshoot. Reset once, get video, but system freezes after checking memory. Reset again, and it's ok. Lot's of resetting going on. Think that perhaps the board is misdetecting the processor, so I disable the jumperfree mode and

Soyo 6BA/Celeron 300A Overclocking Mystery !?
I took all of the chips out and booted with no memory, gave 3 beeps. I unplugged every cord I could and replugged in, have put only one pair of chips in and still nothing. I tried a different monitor and nothing (I am getting no video at all). I reset the cmos to clear it and nothing. The book said it should have

WAAH! Waah!
I had a Radeon 7000ve and someone thought that may have been the problem so I purchased a Asus v9520 video suite. Still would like to use this card, but I still can't get the machine to boot. No beeps, no video, nothing. Tried different PCI slots. Is there a magic BIOS switch or something I'm missing?

No Video after boot, safe mode + VGA mode doesn't help
No beeps 4. No video 5. After a short while, a rapid clicking is heard from the speaker Ahh - yes forgot to point out, this is the 2nd motherboard & CPU from the supplier. Tried the following: 1. Installed RAM in 800MHz PIII PC - worked fine. 2. Installed video card in other PC - worked fine. 3.

No boot after bios changes - 6BA+IV
Everything seemed fine, I remember no beeps what so ever. I didn't clear CMOS before first boot, expecting the default settings to be appropriate for setting up bios. I got no further than bios main menu... Abit decided to shut down and won't post any more. There's not a single beep (nor numerous to start

asus a7m266 problems...
Malke notrea...@invalid.com microsoft public windowsxp hardware Absolutely wrote: All of a sudden, I get no video after XP starts up. Monitor displays Signal Error. Monitor is known good. The fact that you still have video on machine startup and in Safe Mode just means that the card hasn't died completely yet.

System won't boot after flashing BIOS - HELP!
After you delete everything, your disk will be as new (absolutely no information on it). Start creating all partitions with the reverse order, You must boot with CD-ROM support (if not already) and then go to the drive letter of your CD-ROM drive (it is given during startup but for a single partigion hard disk,

HELP - KT7A won't boot/no video - LED "FF"
No video to the monitor. The power light is on, the computer makes the proper sound. I sent to get repaired they said it was the motherboard needed repair, very costly. However, I tried a new power supply from a different Macintosh 7500 and the first time it came up black. The second time after making sure the

VISTA (does not boot) get a BLUE SCREEN
I have recently seen where after installing a new video card and rebooting, W95 kept complaining that the it was not able to set the mode selected for the card I made sure that no video caching or shadowing was enabled. All to no avail. I'm hoping like crazy that I don't have to reformat my hard disk and

G4 Cube Not Powering On After Failed Firmware Update
Any emails I have not authorized are deleted before I see them. "David" <anonym...@discussions.microsoft.com> wrote in message news:01a601c3c769$7f684820$a501280a@phx.gbl... I see the bios and then the windows 2003 startup screen and then the video screen goes blank(black. I do I fix? Thanks david.

IWILL BD100- won't boot after battery change (10 systems)
After 10-20 seconds, turn ON the computer and see if it boots correctly. If it does, fine. If it does not, you may have to reformat the hard disk. -- Rubywand ------- "CHECK STARTUP DEVICE" - Why do I get this message when I try to boot a disk? This error message usually means that there is no diskette in the boot

HELP... My DVD killed my Motherboard.
Device Manager: Video Modem Ethernet Sound Those are the ones you might have problems finding. It's good to know the exact name of the device ( letter for letter ) I have backups of all my drivers anyway. I always keep them and updates of them. On the build going up: Ghost after you get the OS in there with all

KT7A-RAID: No post, no video signal after 1st boot
The very next cold boot it again freezes with no video. This was Jan 31, 2003. I sent them a note indicating the problem was still there. It's been over a week and no response. Were they closed for Chinese New Year. Don't know, their web site didn't say anything (unlike Gainward's that did). After this experience I

No video after startup
spi...@freenet.co.uk uk comp os linux Pep <m...@there.com> wrote: I have just recompiled the kernel on a friends mdk9 and found that when the kernel boots no output is displayed on the screen. I have checked the make and make modules logs and nothing was wrong during the build. Seen this before... Framebuffer.

Lost video after upgrading
The basic problem: after almost a year of working properly, the system suddenly seems unable to boot off of either hard drive on IDE0/1, even though the drives seem When the power was cycled, the machine would not boot: no beeps of any sort indicating the POST had succeeded or failed, no video signal, nothing.

KT7Pro2A does not post after shutdown.
After the beeping, the led's continue cycling from top left red to bottom right red, while the others remain green. It stops again at top left red then beeps a few times then switches to bottom right red (Real Time Clock) and stays there. E-mail me if you would like clarifications. My system is: KT3 ultra-aru333

Windows won't boot after failed video card installation attempt ...
Rick wrote in message ... i recently rebuilt my system with a new board and chip but system will not boot. when power is switched on, the hdd's and cd-rom warm up, but that's it (no "beeps" on start up and no video). *simms snapped in correctly *ide cables changed and pin1 verfied on both hdd's and on board bad